How to Paint on MDF？

How to Paint on MDF

Before you begin painting your new MDF Board project, it is important to know that this material absorbs moisture easily. Because of this, it is essential to use a primer before painting. If you don’t do this, the paint can peel off. Luckily, there are several ways to protect your MDF Board from peeling.

Using solvent-based paints

When painting on MDF, the most common type of paint is oil-based. This type of paint is compatible with a solvent-based primer, but you must thin the paint with a solvent-based thinner. You should also wear protective equipment and use a well-ventilated room when working with oil-based paint.

Before applying any paint to MDF, it is important to clean it thoroughly. You can use a degreaser like Zinsser Universal Degreaser and Cleaner to clean the surface. Once this is done, you can apply primer and topcoat to the surface panel.

Using acrylic paints

MDF (medium density fiberboard) is a popular material for furniture. It is a composite material made from recycled wood fibers and resin. It is extremely durable and easy to work with. The best type of paint to use on MDF is acrylic. It will adhere well to the surface and is also a great choice for a variety of projects.

When painting on MDF, make sure to clean the surface well. You can use a product such as Zinsser Universal Degreaser & Cleaner to remove any residue from the surface.

Using wood filler

One method for restoring the beauty of a wood piece is by using wood filler. This material fixes large, wide grain lines that make wood look cheap. After applying the wood filler, you can sand the area to give it a more luxurious appearance. White oak, for example, is popular for its long, wide grain lines, and using wood filler can help you fix them.

The first step is to apply the filler with a putty knife. Apply the filler to the edges of the MDF. Make sure that the filler goes into cracks and holes and allows two to three hours to dry. Avoid rubbing the filler with your fingers, because this will cause ridges and messy edges. To remove the ridges, you can use a #220 sandpaper to sand away the excess. Once the filler is dry, you can paint.

Prepping the edges

Preparing the edges when painting on MDF is crucial to achieving a good paint finish. The edges of MDF sheets are porous and need to be sealed before the paint can be applied to the surface. Various techniques have been developed to ensure the edges are as close as possible to the finish of the surface. One technique recommended by DIY Doctor is to apply a thin layer of wood filler on the edges before painting. This filler should be pressed in with a putty knife or scraper. Then, it should be sanded down using a sanding block to avoid overabsorption of primer and paint.

Another way to seal the edges of MDF is to use PVA glue or an oil-based filling primer. Ensure that the material is applied evenly and sanded down, since too much sanding will remove the sealing material. After sealing the edges, you can apply a thin layer of drywall compound and primer. You will need to sand down this primer and drywall compound to make the edges smooth and even.

Using a roller

Before using a roller to paint on MDF, it’s important to prime the wood with a water-based primer. This will ensure that the paint adheres properly to the surface. Primer is best applied using a paintbrush in long, even strokes. When painting on MDF, you may need to apply two or three thin coats of primer. After each coat dries, lightly sand the wood.

Painting on MDF is a bit tricky because of its porous surface and flaky edges. If you paint directly on the surface, you may end up distorting the surface or leaving unsightly marks. If you’re using a roller to paint on MDF, you should try to avoid painting the edges, as this can cause the paint to siphon up. It’s also best to paint large flat areas of MDF, rather than edges, because the compressed wood fibers form a tighter bond on large surfaces. You should also make sure the surface you’re painting does not have large pits or holes in it.

Sealing the finish

When painting on MDF, you must seal the surface before applying the paint. This is much more important than the finish layer itself. Sealing is an investment in your project and should be treated as such. Here are some steps to seal the surface. Once you’ve done that, you’re ready to start painting!

Prime MDF with a primer that’s specifically designed for MDF. Then, apply the chosen paint using a brush, roller, or spray gun. Once the primer is dry, evaluate it to determine if it needs a second coat. If there is any patchiness, it’s best to apply a second coat.

Generally, considering the eco-friendly, you can choose to laminate the melamine paper on the MDF as decoration and protection or paste the finished paper. Then you no need to paint on the surface again.

Yodean Decor is a professional laminate paper supplier in China, that provides finish foil, melamine paper and PVC film for wood like the surface boards, if you are looking for durable quality laminate paper, please feel free to contact us for more details.

/0 Comments/by

How to Seal MDF

How to Seal MDF

Using a primer that contains a strong solvent can be hazardous. While it is possible to seal MDF with polyurethane, the fumes can be overwhelming. You should always use a sanding block with a high grit, moving in a circular motion to make the board smooth. After sanding, make sure you clean up the dust.

Solvent-based primers have strong fumes

Solvent-based primers emit fumes, which are toxic if inhaled. They can be dangerous in high concentrations, so you should always wear a mask when working with them. Fortunately, there are some solvent-based alternatives that have low VOC levels.

Oil-based primers are generally better for exterior surfaces. The oil base helps to resist the weather and will last longer. However, you must use it according to the manufacturer’s instructions and wear a respirator. It is also important to wear a mask or eye protection while sanding in between coats of oil-based primer. Furthermore, you should also avoid cleaning it with water.

Although water-based primers are less dangerous, they still produce fumes. If you have asthma, wear eye protection and ensure that your workspace is well-ventilated. Also, be sure to follow the proper precautions for applying this primer: clean and sand the surface with a soft brush or roller.

Polyurethane seals MDF

Polyurethane is a sealant that forms a tough, durable film. It is composed of tightly bonded resin molecules and is the best option for protecting MDF from scratches and impacts. It also has some ‘give’ so that it can absorb impacts and prevent scratches. The best type of polyurethane for sealing MDF is oil-based because it will leave the best finish.

Polyurethane can take up to 24 hours to dry completely. It can also protect MDF from water damage. MDF is a man-made wood product made from wood fibers that have been compressed. It is easier to work with than solid wood, and it is much more affordable.

Edge filler

You can easily seal the edges of MDF cabinets with the help of a thin coat of PVA glue or oil-based filling primer. Apply the glue on the edges evenly and let it dry before sanding. Care must be taken not to sand the edges too far or else the glue will peel off. You can also use a primer or drywall compound to prime the edges of MDF cabinets.

Before you apply the primer or paint, you should prime the MDF board first. Prepare the area with a drop cloth. Next, apply the oil-based primer to the face layers and edges of MDF. To apply the primer, use a roller. Then, smooth the newly primed face layers and edges with 600-grit sandpaper.

Solvent-based sealers

When it comes to sealing MDF, a polyurethane coating is a good choice. This type of coating forms a tough film, containing tightly bonded resin molecules. Once it has dried, this type of coating protects against water damage by preventing it from penetrating the surface. It also offers a slight ‘give’ that resists impacts and prevents scratching. But it must be noted that a polyurethane-based coating should only be used on MDF.

MDF is generally porous on the edges, and sealing these edges will prevent the board from soaking up paint and moisture. It also ensures that the paint adheres properly to the surface. A wood filler is a great way to seal the edges of MDF. Apply it with a putty knife or your fingers, then sand the surface. Once dry, remove the excess filler with a clean dry cloth.

Water-based sealers

Water-based sealers for MDF come in different varieties. Those that are clear allows the surface to receive paint or varnish, while those that are white only allow for painting. These sealers dry within 30 minutes. They can be re-applied within two hours. Depending on the type of finish you want, they are also available in various colors.

Acrylic primer is a good choice for sealing MDF. It comes in white, but it can also be purchased in grey or darker colors. It has a low odor and dries quickly. It is easy to apply with a brush. However, it is recommended to use two coats to get a decent finish.

 

/0 Comments/by

What Is MDF?

What Is MDF?

What Is MDF

MDF stands for medium-density fibreboard and is an engineered wood product. It is made by breaking down wood into small fibres and mixing them with wax and a resin binder. These fibres are then pressed together at a high temperature into panels. MDF is a lightweight alternative to plywood and has several advantages.

Veneered MDF

Veneered MDF sheets are an excellent alternative to solid wood. They can be used for furniture manufacturing and wall panelling. The edges of the boards can be finished with matching iron-on veneer edging strips. Veneered MDF is an environmentally friendly choice. It uses up to 95% of the tree’s harvested biomass.

Veneering requires careful handling and processing to prevent delamination. It should be checked for moisture content with a moisture meter that penetrates the veneer face. The moisture content should be between seven and nine per cent. Higher moisture content can cause checks and delamination. If you see a check in the face of the veneer, it is most likely that it has delamination.

Veneering is a process that creates flat panels for furniture and woodworking projects. It also provides a way for cabinetmakers to create furniture that features exotic wood. Veneering enhances the look of the project and design space.

MDF is a type of MDF

MDF is a common material that is made from wood mill residues. The wood fibres are ground to a fine powder, combined with resin and wax, and then heated and pressed to form dense sheets. The end result is a very smooth, uniform surface that can be painted or sealed. Unlike plywood, MDF does not contain any voids or knots.

There are three main grades of MDF, each with varying qualities. The standard grade contains wood fibres and a synthetic resin adhesive. The lightweight version has less wood fibres and is slightly weaker. Finally, high-density MDF is a tougher board with more wood fibres packed in. These qualities make MDF suitable for many applications, including the back of furniture, drawer bottoms, and flooring.

It is lighter than plywood

Plywood is a manufactured product made by binding thin sheets or fine layers of wood veneers together. It is very strong and dimensionally stable. However, it is also very expensive. It is also difficult to mould and cut, and it requires a veneer or a laminate finish. It also holds nails well.

MDF is softer than plywood, making it easier to cut. This means that it won’t crack or splinter and is better for carving intricate trim. Plywood also has a rough edge, which can result in ragged edges. MDF is a better choice for carving intricate trim than plywood.

If you’re looking for a lighter wood alternative for your next project, MDF may be the right choice. It’s an engineered wood composite made from fine pieces of wood and a resin binder. It is slightly more expensive than plywood, but it’s also lighter and stronger.

It is resistant to moisture

Moisture-resistant MDF is a popular material for cabinets, wall panels, and flooring in homes. It is resistant to water and is easily sanded, milled, and takes most types of paint, veneer, and adhesives. It is ideal for kitchens and bathrooms, but can also be used in tropical areas.

Moisture-resistant MDF is not waterproof, but it is resistant to high humidity and rain. However, this material should be treated with care and should not be exposed to extreme wet or humid conditions. In addition, the material must be regularly maintained or the protective coating will wear off over time. Moreover, if it is exposed to moisture for an extended period of time, the wood may warp or bend.

To waterproof MDF, you can use shellac, PVA glue, or moisture-resistant paint. However, it is important to use a water-based product that is designed specifically for MDF. Make sure you choose a product that is 100 per cent waterproof, as some water-based polyurethane will not adhere to MDF surfaces.

It emits formaldehyde

MDF is a type of wood that emits formaldehyde. This chemical is used in the manufacturing of furniture. It is also used in the preservation of organs and tissues. In addition to its uses in the woodworking industry, formaldehyde is also used in various cosmetics and food products. It is classified as an additive under code E240.

There are several factors involved in the emission of this chemical, but most studies have focused on the amount of MDF and the glues used to create it. There are likely other factors involved in the production of MDF as well.

Generally, the MDF needs to apply the finished paper on the surface to enhance the resistance features, and also play a decorative role. If you are looking for a professional finish foil paper manufacturer, please don’t hesitate to contact us for more details.

/0 Comments/by

How to Remove Laminate Sheet Flooring

How to Remove Laminate Sheet Flooring

Fortunately, there are some steps that can make removing laminate sheet flooring a breeze. The first step is to ensure that you don’t damage the transition pieces that separate adjoining rooms. Then, use a pry bar to remove the adjoining floor planks. Make sure you don’t remove the u-track, which will allow the adjoining floor planks to come off with it.

Floor scraper

If you’re planning to remove laminate sheet flooring, you’ll need a floor scraper. These tools are great for scraping away the surface layer of your flooring and are 10 times more effective than manual scrapers. Floor scrapers are also useful for removing old tiles, carpet tiles, vinyl sheeting, and cement and plaster from walls.

You can also use a heat gun to loosen any remaining adhesive. Make sure to use a low setting, and then gently wave the heated gun around the joint between the flooring and the underlayment. This will help loosen the glue and allow the floor scraper to scrape it up.

First, remove any existing laminate sheet flooring. The glued-on planks are usually attached to the subfloor or intermediate layer. If you have a wide area to scrape, a reciprocating saw with a floor scraper attachment may be the best tool. Glue remover solution is available at hardware stores and will help dissolve the adhesive. Be sure to wear safety gear and follow the instructions on the product.

Heat gun

If you’re looking for a faster way to remove laminate sheet flooring, you can use a heat gun. You should use a low-setting heat gun and hold the nozzle a few inches above the flooring. After the glue has become loose, you can lift the edges and pull the flooring off.

Once the glue has loosened, you can use the heat gun to loosen the top side of the flooring. If the glue is too tough to loosen, you can use mineral spirits or water to loosen it. Be sure to carefully follow the manufacturer’s instructions before using the heat gun.

The next step is to remove the existing tile. Once the tiles are loose, you can turn the heat gun up and use a putty knife to remove the underlying adhesive. If the tile is broken, you may have to pry up each tile individually.

Adhesive residue

If your laminate floor has a stubborn adhesive residue, you can use a putty knife to scrape the glue off. Alternatively, you can use a single-sided razor blade. Another option is to use liquid dishwashing soap mixed with warm water. The solution should be applied to a clean cloth and left on the floor for several hours. In a pinch, you can use plastic wrap to protect your laminate floor from moisture while you work.

First, you should mix some dish detergent and warm water and apply it to the adhesive residue. You should notice that it starts to dissolve and starts coming off. However, you should avoid applying too much of the solution as this could deteriorate your flooring. You can also try to paint thinner as it will help you get rid of old adhesive residue. Just make sure that you soak the area first.

Sticky residues can make your laminate floor look bad. As they attract dust and dirt, they build up and form a lumpy mess. This can be the result of an adhesive spill or using the wrong cleaning solution. Thankfully, there are several simple ways to clean sticky laminate floors.

Disposal of laminate sheet flooring

When it comes to disposing of laminate sheet flooring, you can choose to recycle it or dispose of it in a landfill. Recycling is a good option because it will not pollute the environment and can be a great way to reduce waste. However, some recycling centers do not accept old laminate sheet flooring, so it is important to check with a local manufacturer for information.

Some people choose to burn their laminate flooring, but this is not a good idea because it causes air pollution and wastes raw materials. Although this method might be beneficial in some cases, it has negative effects on the environment. Instead, you can try to recycle the fibers and use them to make other materials.

If you choose to recycle laminate flooring, it is important to remember that up to 85% of its mass can be recycled. This means that most of the flooring can be turned into fibers or wood chips. However, the process is too complicated for most local recycling facilities. You may have to take the old flooring to a landfill yourself, which will require more time and work.

/0 Comments/by

How to Remove Laminate Sheet From Countertop

,

How to Remove Laminate Sheet From Countertop

If you’re thinking of replacing the laminate on your countertop, there are several things to consider before you take on the project. First, you’ll need to know how to remove the existing sheet. You can do this with the help of a professional who knows how to remove the old laminate sheet. You may also need to cut the laminate. In addition, you will need to install buildup strips underneath the countertop before you can begin the process of removing the old laminate.

Removing laminate from a particle board framework

Before attempting to remove a laminate sheet from a particle board framework, it is important to clean the surface thoroughly. If you do not, the heat may cause dust and other debris to seep into the wood fibers. A heat gun, which is similar to a hair dryer, can be used to soften the adhesive and loosen the laminate.

First, use a putty knife to cut away any chunks of glue. Next, take the sanding paper and work the glue off with a small sanding machine. If the glue is difficult to remove, you may have to use acetone or a general-purpose thinner.

Cutting laminate

The first step in cutting a laminate sheet from a countertop is to prepare the work area and make sure the material is straight and level. This will help ensure that you do not move the material while cutting. After you have prepared the work area, you should prepare a piece of scrap board to hold the laminate sheet.

To do this, you will need to cut a piece of wood to fit over the edge of the countertop. The wood strip should extend out a few inches beyond the edge of the countertop. The wood strip will act as a temporary barrier to keep the sheet in place. Next, place the new sheet face-up over the wooden strips. If the laminate sheet is loose, it will not bond properly to the countertop.

Installing buildup strips underneath the countertop

Once you have removed the laminate sheet from the countertop, you should install the buildup strips beneath it. You can install the buildup strips using contact cement. However, if the laminate is loose, you will have to use a fresh coat of adhesive. First, apply a contact adhesive to both the underside and the top of the substrate. Once this tacky glue is dry, roll the end cap into place using a J-roller. Next, use a file or router to trim the end cap down to the countertop edge.

Once the wood strips have been installed, install the new laminate sheet. Make sure to use a J-roller to smooth the surface. Next, use the router to trim any excess laminate. Use a flush-trim bit to cut the edges flush with the edge of the countertop.

Removing old laminate

Before you replace your countertop, you’ll need to remove your old sheet. Cut the wood strips about 4 inches longer than the countertop. These strips will act as a barrier between the countertop and the new laminate sheet. You can use a jigsaw to cut the wood strips. You’ll then place the new laminate sheet face up on top of the wood strips. Be sure to position it properly so that it doesn’t touch the other surface. Then, use a J-roller to press it down.

Start at one end of the countertop. You’ll need to smooth out the entire surface with the J-roller. Once the entire surface is smoothed out, use a router equipped with a flush-trim bit. Trim the excess laminate so that the edge meets the countertop edge.

Cleaning laminate countertops

Fortunately, there are many methods for cleaning laminate countertops. You can buy degreasers at any hardware store or use household items such as white vinegar and rubbing alcohol. For the best results, dilute the alcohol with two to three parts water. You can also use Lysol, which is a disinfectant that won’t harm the laminate. You should avoid using these products daily, however.

The best way to clean a laminate countertop is to remove any spills immediately by rinsing the area with clean water. After cleaning the area, wipe it dry with a soft microfiber cloth. However, you should avoid putting too much water on the surface, as moisture can cause it to warp and shrink.

Gluing new laminate over old laminate

You can install a new laminate countertop over an old one if you want to change the look of your kitchen. First, you need to cut the new laminate to fit over the old one. Then, you should apply contact cement to the back side of the new countertop. You should also make sure that the countertop surface is smooth and flat. Make sure that you clean off all dust to avoid mixing it with glue.

Once you have the surface prepared, you need to apply the contact cement to the old laminate. It will stick to itself but will not stick to the new laminate. To make sure that your laminate is completely covered, place a thin towel over the area where you want to re-glue. After applying the contact cement, you need to wait for it to dry. Alternatively, you can also use a hair dryer or a heat gun.

Yodean Decor is a leading China supplier of lamination paper for the artificial board, with our own factory to make finish paper foil, edge banding tape and PVC film, if you are looking for stable quality furniture paper at a wholesale price, please don’t hesitate to contact us for more details.

/0 Comments/by

How to Cut Laminated Sheeting

,

How to Cut Laminated Sheeting

The first step to cutting laminate sheeting is identifying where to cut. This step is relatively easy. You can use a circular saw or a jigsaw. The next step is to clean the file using lacquer thinner or the solvent recommended by the adhesive manufacturer. Using a utility knife is also an option. Alternatively, you can purchase a special file that is made specifically for plastic laminate. Regardless of what type of tool you use, you should always cut the laminate sheeting at an angle.

Using a utility knife

If you don’t have a table saw, you can cut laminate sheeting with a utility knife. Many utility knives are fitted with specialized blades to cut laminate. Using a straightedge to guide the knife is crucial. Other methods include using a jig saw, circ saw, or table saw with a fine-tooth blade. Before cutting, you should cover the surface of the sheeting with masking tape to prevent chipping or ripping.

To cut laminate sheeting, you must prepare a worktable that has enough support for the blade. The worktable surface should be a sturdy surface, such as a piece of plywood or metal. You should also use a drywall square to trace the shape you wish to cut. It helps to start with the corner to minimize the amount of cutting. When you are done with the backer board, you can turn your utility knife on the other side to make the next cut.

Using a jigsaw

If you are looking for a cheap way to cut laminate sheeting, consider buying a jigsaw. These tools have specific safety guidelines that should be adhered to. When using a jigsaw to cut laminate sheeting, you should use a blade with reverse teeth. These blades are designed to cut on the downstroke and will not rip the laminate layer. They are also ideal for cutting medium to high-tooth-count laminate.

You should use a jigsaw that has a variable-speed setting. This type of tool is the perfect choice for cutting a variety of materials. You must also make sure that you are using a blade that is compatible with the type of material you’re working with. You should also make sure to use a 1/2-inch drill bit to ensure you get the most out of your jigsaw.

Using a dremel

Using a dremel to trim laminate sheeting is a very simple process. The first step is to make a template on plywood or masonite. You can use a partial template to cut other parts of the opening, but a full template is easier to work with. Next, run the dremel around the edge of the template. The trimmer’s shaft will ride on bearings, guiding it in a straight or curved line.

The next step is to prepare the laminate sheeting for cutting. Before starting, you’ll need a piece of backerboard or a large sheet of plywood. This is a useful backing for laminate. You can then cut the laminate sheeting using a dremel tool fitted with a carbide blade. It will cut the laminate sheeting in a fraction of the time of a conventional razor blade, and you’ll experience less frustration and breakage. You won’t have to fold the cut lines, either. The cutting bit is very hot during the process and you’ll want to set it aside while it cools.

Using a circular saw

Using a circular saw to cut laminate can be a hassle. The sharp edges are dangerous to the eyes, and the blades can kick back and cause cracks and chips. If you don’t have much experience cutting large sheets of laminate, consider a hand cutter. These machines are available at local supply stores for under $20. You’ll need to know how to use them properly and how to prevent problems.

Before using a circular saw to cut laminate sheeting, you’ll want to make sure you have a blade that has plenty of fine teeth. Then, you’ll want to carefully mark the line on the sheeting to make sure you don’t cut off a corner or another part of the laminate. Once you’ve marked the line, you can use duct tape or painter’s tape to protect the finish of the laminate.

Using a tin snips

The most effective way to cut tin roofing is to plan your cuts beforehand. You will need to measure the distance between roof vents and chimneys and mark the cuts. You will also need to use a carpenter’s square. Be sure to mark both sides of the tin. Be careful when handling tin as it is very flexible. Therefore, you should not let it fall.

If you are using a tin snips, you should use your dominant hand to hold the tin snips. Hold the sheet metal with the other hand, and start cutting along the line that you have drawn. Repeat until the entire piece is cut. If there are burrs on the sheet, you should use an angle grinder equipped with a polishing disc to remove them.

/0 Comments/by

How to Lmaminate MDF Sheet

How to Lmaminate MDF Sheet

The first step in learning how to laminate MDF sheets is to thoroughly clean the material to remove any residue or unwanted stains. Use a solution of Trisodium Phosphate or water to clean the surface, and make sure to wipe it dry completely. Next, use sandpaper to clean the surface to ensure proper paint adhesion and primer adhesion. This step is similar to wiping a counter.

Step 1: Cut the sheets of MDF and laminate into the desired size. Each sheet of MDF should be slightly larger than the size of the laminate.

Step 2: Apply the adhesive to one side of the sheet of MDF.

Step 3: Lay a sheet of laminate on top of the MDF with the adhesive side facing down, and press gently until you have a good contact between both materials.

Step 5: Repeat these steps for the other side of the board.

Step 6: Let the boards dry overnight.

Step 7: Cut the parts of each board into the desired size, using a jigsaw or circular saw.

Step 8: If desired, paint both sides of each piece with varnish and let dry before assembling.

Step 9: Assemble the board with a drill and screws.

Step 10: Attach a piece of plywood to the bottom of each end of the board, using clamps and glue

Melamine board is also a form of direct laminate. The product is created using 300 to 500 pounds of pressure per square inch. Melamine is then molded into a plastic sheet by applying a chemical to the melamine paper layers. Then, the resulting laminate is bonded together with particleboard or another type of backing material. While the process is complex, the final product is both durable and beautiful. It is a great choice for countertops and cabinets and is available at many price ranges.

Whether you’re building a home or remodeling an existing one, MDF laminate sheet offers a range of benefits. Its design is similar to particle board, but with a more durable, scratch and heat-resistant surface.

If you are looking for laminate sheets for MDF surface protection and decoration, you come to the right place. Yodean Decor is a leading laminate sheet supplier and manufacturer in China, producing different lamination sheet – finish foil, melamine paper, PVC decoration film, and PVC edge banding,  contact us if you have a great deal with lamination paper for wood like surfaces, free sample and fast delivery available.

/0 Comments/by

Tips to know PVC flooring

pvc flooring

1、What is PVC flooring?

 

PVC flooring is semi-rigid polyvinyl chloride flooring, based on PVC resin, consisting of PVC resin, calcium carbonate, pigment, dye, surface treatment agent.

2、Is PVC flooring eco-friendly

Yes. Tested by the relevant state departments, the pvc flooring is non-toxic, harmless, zero formaldehyde content, many indicators have reached the relevant international standard even better. Therefore, the pvc flooring is the eco-friendly material that promot by the China Building Materials Circulation Association. Indoor Environment Professional Committee call it as “top ten safety standards floor “.

3、What are the advantages of pvc flooring compared with wood flooring?

Solid wood flooring is expensive, very easy to deform after moisture, and easy to crack and shrink after air-drying, so that the seams become larger. In addition, if the solid wood flooring is not properly maintained, it will result in mildew and insects. In contrast, pvc flooring has a more excellent performance, not be expansion and deformation after heat and moisture, with features of anti-corrosion and good mothproof ability. The maintenance of PVC flooring is also particularly simple.

4、What are the advantages of pvc flooring compared with tile and stone?

First of all, tile, stone is a very hard material, and the surface is smooth, which inevitably causes walking feet feel hard, the ground has water is very easy to slip, causing injury. And pvc flooring due to the advantages of their own materials, both the solidity of stone and organic materials, softness, so that people walking feet feel very comfortable, while having “water more astringent” characteristics, even if accidentally fallen, will not hurt the person.

5、Is Pvc flooring strong and durable?

PVC flooring contains stone powder composition, decided the product has superior pressure resistance, added resin makes the PVC flooring with a certain softness. When meeting the impact of heavy objects, the PVC flooring will not be broken like tile, stone, so the resistance of PVC flooring is very good.
Wear resistance is a great concern. Actually, the pvc composite class floor surface using UV wear-resistant coating, the use of the process through photochemical reaction, the wear resistance of PVC flooring will increase with the use of time. In addtional, the UV layer absorb the ultraviolet light, so that the floor printing layer will not change color, which greatly slowing down the aging rate of the PVC flooring, extending its service life. In addition, the wear-resistant layer above the printing layer is very hard, wear-resistant revolutions are in more than 30,000 revolutions.

6、What glue is used in the construction of PVC floor? Is there an odor after the pavement? How long can move in?

Construction PVC flooring needs to use special glue, this glue is water-soluble glue, and is safe for the human body, as confirmed by the national environmental protection testing department. This glue does not contain toxic heavy metals and toxic volatiles, and there is no odor after paving. After completing the PVC flooring construction, you can move in after opening the window ventilation for 48 hours.

7、The original ground is tile, to shovel to lay PVC flooring?

The answer is no. No need to shovel off, such as a paving sheet, the PVC flooring can be laid directly on the top after only a simple treatment of the gap. For paving coil, it can be done directly on the floor tiles with self-leveling treatment and then paving. The construction process of PVC flooring has little noise, easy and fast.

8、If the PVC floor daily maintenance simple?

Yes. Only need to wipe with wet dunnage on weekdays. Through the body, structure flooring is best to be able to wax once after the construction is completed, and then wax regularly depending on the situation, it can be kept as bright as new. Laminate structure floor is no need to wax, only daily cleaning can be.

/0 Comments/by

How to Paint Wood-Grain Laminate

How to Paint Wood-Grain Laminate

If you’ve ever wanted to change the color of your laminate furniture, you can easily do so by following a few steps. First, you must tape off your work area and cover any surfaces you don’t want to paint. Next, you must prime the surface of the laminate furniture. The purpose of priming is to give the paint a smooth finish and prevent it from peeling off once it has dried. Listed below are the steps you need to follow in order to successfully paint your wood-grain furniture.

Primer

Before you paint wood-grain laminate, it is necessary to prime all surfaces with a suitable primer. Choose one that is specifically made for laminates, such as Rust-Oleum Universal Bonding Primer. Using a paint roller, roll the primer on the wood-grain surface in a smooth motion. Once the primer has dried, you can then start painting. If the primer starts to show through, you may need to apply a second coat.

To start painting, disassemble the furniture first. Remove the hardware, if necessary. Next, apply primer using a roller, preferably a 4” diameter roller. Remember that the primer will show brush marks, so use a fine sandpaper to fill in the gaps. If the paint has a strong smell, it’s a good idea to work in a well-ventilated area or wear a mask.

Sanding

Before you start painting, sand the laminate surface with fine-grit sandpaper. Use a motorized orbital sander if your surface is large. When finished, wipe off any dusty residue with a tack cloth. Then, prime the laminate surface with a high-quality, laminate-specific primer. This step will prevent peeling and lifting of the paint in the future.

Once you’ve sanded the laminate, use protective gear and 150-grit sandpaper. You can use a hand sander or an electric one. When finished, the laminate will look scuffed and rough. Then, apply a clear coat to seal it. This step is optional, however. For a smooth finish, use two coats of a polyurethane glaze.

Sealant

A sealant is a thin layer of finish applied to the surface of a wood-grain laminate floor. Some sealants come in several layers. Make sure that each layer is fully dry before applying a new layer. Sealants may cause reactions or damage to the floor if applied too frequently. When buying a sealant, be sure to check the label for recommended use with your type of wood-grain laminate floor.

Depending on the type of flooring, you can choose a clear, white, or tan sealant. These products are designed to form a strong bond between the laminate and sealant. Use the sealant on your floor to cover cracks in the floorboards or tiles. Leave the sealant to dry for 24 hours before using the floor. Using a floor buffer can improve the shine of the laminate floor.

Using a wood-grain rocker tool

Using a wood-grain rocking tool can be a fun way to add a natural look to your painted furniture. These tools come with a variety of features, including a flat brush, a graduated comb, and a wood-grain groove. By carefully dragging the tool across the surface, you can create the look of wood graining on your furniture.

To get the best result, make sure you carefully determine the direction of the wood grain. This is a tricky task if you’ve never seen a real wood grain, but it’s important to keep in mind that the grain runs vertically on a vertical surface. For a horizontal surface, the grain runs horizontally. This is especially important if you’re painting a panel with a wood-grain finish.

Applying a polyurethane glaze

If you’re applying a polyurethane glaze to wood grain laminate, there are several things you need to know. First, the type of finish you’re looking for is critical. You’ll want to select one that dries quickly and evenly. You should also wear a respirator when working with oil-based polyurethane, as it contains more volatile organic compounds than water-based polyurethane.

When applying a polyurethane glaze to wood grain laminate, you must use a paintbrush or roller with natural bristles. Do not use an exploded-tip synthetic brush, as these may introduce air bubbles into the finish. Apply the polyurethane in two coats, one after the other, to achieve the best results. The polyurethane finish will look glossy and protected for many years.

Creating a grain effect

Before you start applying paint to your wood-grain laminate, you should prime the surface first. If the table is made of wood, you can use a darker paint color instead of a medium tone. A rocker tool can be used to apply the paint in sweeping motions. This method will help you create a grain effect on your laminate. It will also help you determine the direction of the wood grain, which is typically horizontal or vertical.

Using a faux wood glaze on a non-wood surface is another way to create a grain effect. This technique requires several layers of paint, and involves a bit of trial-and-error. To get an authentic-looking grain pattern, choose a wood-toned paint. Primary colors can be used to create Art Deco patterns or a wood-toned paint.

/0 Comments/by